Previous
Next

EST-EPS Elastic

Applications

•  Additive for ESTonetex mortars, concrete and plasters

•  Increasing the strength of mortars

•  Improving the adhesion of mortars on cement bases

•  Regulating the absorption of ceramic surfaces (thermo-clay, brick, etc.) before coating them with mortar in decoration or theming

Technical specifications

Reference1405 (5 L) / 1406 (10 L) / 1407 (25 L)
Packaging5 L, 10 L or 25 L plastic container
AppearanceColourless (milky appearance)
Density1.04 g/cm³
Solids by weight60 %
DiluentWater
Dosage1 part resin to 3 parts water (1:3), replacing part of the mixing water
Application temperatureDo not apply below 5 ºC
Shelf life18 months in a sealed container, in a cool place (5 to 25 ºC)

Elastomeric aqueous dispersion with high elasticity and a high level of recovery, and very good alkali resistance. It improves the physicochemical properties of cementitious products, increases the adhesion of mortars on cement bases, increases compressive and flexural strength and improves resistance to UV rays. Full technical documentation is in the technical data sheet downloadable above.

How is it mixed?

•  Homogenise the contents of the container by stirring thoroughly

•  Mix with the mortar in the appropriate ratio, replacing part of the mixing water: 1 part resin to 3 parts water (1:3)

•  Mix with a stirrer at low speed so as not to introduce air

•  Do not apply below 5 ºC

To regulate the absorption of thermo-clay surfaces in theming work, a mixture of 1 part product and 8 parts water is applied to the surface.

Substrates

The substrates onto which the product is applied mixed with mortar must be clean, dry and free of any dirt.

Compatibility

•  ESTonetex mortars, concrete and plasters: it is added to the mixing water; with ESTonetex Forte a mix of water and EST-EPS Elastic (1:3) can be added for a specific finish on EPS/XPS; see the rest of the ESTonetex mortars

•  Cement bases and ceramic surfaces: it increases the adhesion of the mortar on cement bases and regulates the absorption of ceramics

Observations and precautions

Do not apply below 5 ºC, with a risk of frost in the following 24 hours, or in areas of strong direct sun. Wear gloves, goggles and a mask; do not ingest or inhale. Professional product: always consult the safety data sheet before use.

Storage

Store for up to 18 months in a sealed container, in a cool place at a temperature not below 5 ºC nor above 25 ºC and out of direct sunlight. Expired product must be disposed of in accordance with current legislation.

Complementary materials

•  ESTonetex Forte: thin-layer mortar for polystyrene to which EST-EPS Elastic can be added

•  ESTonetex mortars: the rest of the range of mortars that can be modified

•  EST-S Imprimer: bonding primer for mortars on smooth substrates

Frequently asked questions

What is EST-EPS Elastic used for?
To modify ESTonetex mortars, concrete and plasters: it improves protection, waterproofing, compaction, adhesion on cement bases and compressive and flexural strength.

What dosage is used?
It is mixed with the mortar replacing part of the mixing water: 1 part resin to 3 parts water (1:3).

How is it mixed?
Stir the container thoroughly and mix with a stirrer at low speed so as not to introduce air.

Can it be used with ESTonetex Forte?
Yes: ESTonetex Forte can be mixed with water or with a mix of water and EST-EPS Elastic (1:3) for a specific decorative finish on EPS/XPS.

Can it be used to regulate the absorption of ceramics?
Yes, on thermo-clay, brick, etc. surfaces before coating them with mortar in decoration or theming: a mix of 1 part product and 8 parts water is applied.

At what temperature can it be applied?
It must not be applied below 5 ºC.

Which containers and references does it come in?
In plastic containers of 5 L (REF 1405), 10 L (REF 1406) and 25 L (REF 1407).

How does it differ from EST-Gel Cal and EST-S Imprimer?
EST-EPS Elastic is a multifunction additive in aqueous dispersion that improves the strength and protection of the mortar. EST-Gel Cal is a lime plasticiser that improves workability (stone and brick grouting) and EST-S Imprimer is a primer applied onto the substrate before the mortar.

How long can it be stored?
Up to 18 months in a sealed container, in a cool place between 5 and 25 ºC.

👉🏻 Remember that our shop is a DIGITAL CATALOGUE. You can request a quote if you are in Spain, or find our official international distributors.

Solicitud de presupuesto

También podría interesarte

You might also like