EST-3 Plus N
Applications
• Absorbent natural and artificial stone, microcements, mortars and concrete, even freshly set and highly alkaline
• Mineral coatings and paints, facing brick, roof tiles, lime stucco, terracotta floors, absorbent ceramics and slate
• Facades, refurbishment, heritage, theming and civil works
• Pool copings, skirtings, public squares, homes, hotels and restaurants
Technical specifications
| Reference | 1200 (1 L) / 1201 (5 L) / 1202 (10 L) |
| Packaging | 1 L, 5 L or 10 L plastic container |
| Colour | Milky in the container; colourless finish (at higher concentration it may slightly enhance the tone of the base) |
| Density | Approximately 1.0 |
| Sd value | Approximately 0.02 (high breathability) |
| Dilution | From 1:14 (general water repellency) to 1:6 (maximum protection) in water |
| Consumption | Between 150 and 400 ml/m² of ready-to-apply product, depending on the surface |
| Application temperature | From 5 ºC (surface and ambient) |
| Drying time | Between 4 and 24 hours; the repellent effect appears after 24 hours and is fully cured in approx. one week |
| VOC content | Concentrate: 5 g/l; as used (1:6): less than 1 g/l (category h BA, maximum 30 g/l) |
| Shelf life | 24 months in a sealed container, in a cool place (5 to 25 ºC) |
Oil-repellent mineral water repellent that leaves no film: it penetrates the pores of the base and gives long-term protection against waterborne pollution, frost and the growth of micro-organisms, makes it harder for dirt to adhere in depth and makes cleaning easier. It is treated with BioFilmStop technology, which inhibits fungi and micro-organisms (DIN-UNE EN 15457:2008). Once dry, it does not alter the flammability of the base or spread flame. Full technical documentation is in the technical data sheet downloadable above.
Substrates
The base must be completely dry and its pores clean, free of salts, micro-organisms, grease, release agents, waxes, lacquers or construction debris, so that the treatment penetrates well. Although it is water-based and can technically be applied to a damp base (in certain cases of capillary dampness), the concentration or the number of coats must then be increased. Before applying, protect the surrounding surfaces that should not be treated. EST-12 can be used to clean the base.
How is it diluted?
It is applied diluted in water: from 1 part of product to 14 of water (1:14), for general water repellency of facades and indoor and outdoor work, up to 1 part to 6 of water (1:6), recommended for pavements, pools and surfaces in continuous contact with water or immersion, which gives maximum protection. The greater the dilution, the weaker the oil-repellent and tone-enhancing effect; the higher the concentration, the stronger the protective and tone-enhancing effect.
How is it applied?
Shake well before use. Apply with a brush, roller or sprayer, 2 to 3 coats, each over the previous one while still wet (two coats in one), avoiding leaving unabsorbed material on the surface. On facades and vertical surfaces, apply from bottom to top to avoid runs. On horizontal surfaces and low-porosity bases, apply only the amount that penetrates the pore and remove any excess with a clean cloth before it dries. Clean the tools with water immediately after use. You can watch the explanatory video on mineral water repellents.
Compatibility
• ESTonetex mortars: the technical data sheets of ESTonetex TXT, ESTonetex Park, ESTonetex Extreme, ESTonetex Extreme SR-MR, ESTonetex Forte, ESTonetex Sulfo, ESTonetex Texturest and ESTonetex Restaura recommend applying EST-3 Plus N as the final protection once the work is finished (on ESTonetex Extreme SR-MR diluted 1:6)
• Alkaline bases: suitable on mortars and concrete, even freshly set and highly alkaline
• Maintenance on pavements: clean with neutral soaps; aggressive cleaners can reduce its durability and waxes must not be used, as they will be repelled
Observations and precautions
Durability depends on use, traffic, wear and the type of base, and the treatment is easily renewed without stripping: just clean and reapply. On horizontal surfaces where the passage of water is to be reduced, repair cracks and fissures first; on standing or submerged water it may reduce it, but does not prevent it. On low-porosity surfaces (marble, granite) or where no optical alteration is acceptable, consult our technical service. Do not apply in areas strongly exposed to the sun. Application temperature from 5 ºC. Wear gloves, goggles and a mask; do not ingest or inhale. Professional product: always consult the safety data sheet before use.
Storage
Store for up to 24 months in a sealed container, in a cool place, at a temperature not below 5 ºC nor above 25 ºC. Protect the product from heat and avoid direct exposure of the containers to the sun. Once opened, close the container immediately after taking the amount needed and use only clean tools, so that no dust or dirt gets in. Expired product must be disposed of in accordance with current legislation.
Complementary materials
• ESTonetex TXT, ESTonetex Park, ESTonetex Extreme, ESTonetex Extreme SR-MR, ESTonetex Forte, ESTonetex Sulfo, ESTonetex Texturest and ESTonetex Restaura: mortars protected with this water repellent
• EST-12: detergent cleaner to prepare the base
• EST sprayer: to apply the diluted product
• EST-7 and EST-Multilitio: the drying water repellent and the consolidant of the range
Frequently asked questions
What is EST-3 Plus N used for?
To make absorbent mineral bases water repellent (mortars, concrete, stone, microcement, pavements and facades): it reduces water penetration, curbs the growth of fungi and micro-organisms and makes it harder for dirt to adhere.
What dilution ratio is used?
From 1:14 in water for general water repellency of facades and indoor and outdoor work, up to 1:6 for maximum protection on pavements, pools and areas in continuous contact with water.
Does it change the appearance of the surface?
It does not alter colour or gloss: it is colourless once applied and leaves no film. At higher concentration it may slightly enhance the tone of the base.
How long does it take to work?
It dries in 4 to 24 hours. The repellent effect begins to appear after 24 hours and is fully cured in approximately one week; the oil-repellent effect is not complete until at least 4-7 days after application.
What is its coverage?
Consumption ranges between 150 and 400 ml/m² of ready-to-apply product, depending on the type of surface.
Can it be applied on freshly set or highly alkaline mortar?
Yes: its technical data sheet states that it is suitable for mortars and concrete even freshly set and highly alkaline. That is why the data sheet of EST-7 recommends it for fresh cement and highly alkaline bases.
How is a treated surface maintained?
With neutral soaps: aggressive cleaning products can reduce its durability and waxes must not be used. To renew the treatment, simply clean the base and apply it again, without stripping.
How does it differ from EST-7 and EST-Multilitio?
EST-3 Plus N is an oil-repellent water repellent that leaves no film and is applied on dry bases, including highly alkaline ones. EST-7 is a drying, consolidating water repellent designed for damp surfaces and heritage restoration. EST-Multilitio is not a water repellent: it is a lithium silicate mineral consolidant to harden the base.
Which containers and references does it come in?
In plastic containers of 1 L (REF 1200), 5 L (REF 1201) and 10 L (REF 1202).
How long can it be stored?
Up to 24 months in a sealed container, in a cool place between 5 and 25 ºC and protected from direct sun.
👉🏻 Remember that our shop is a DIGITAL CATALOGUE. You can request a quote if you are in Spain, or find our official international distributors.
Solicitud de presupuesto
-- or --