Previous
Next

EST-Floor

Applications

•  Decorative stamped concrete and microcement pavements

•  Roads, pedestrian lanes, garage floors and concrete floors

•  Decorative and industrial floors outdoors

Technical specifications

Reference1209 (5 L) / 1210 (25 L)
Packaging5 L or 25 L plastic container
AppearanceTransparent
Density1.02 ± 0.01 g/cm³
Solids25 ± 1 %
Viscosity (Ford cup 4 mm)16 ± 1 s
Coverage8 - 10 m²/L on stamped concrete
Application temperatureBetween 5 and 30 ºC (ambient and substrate), without excessive wind
Touch dry1 - 2 hours
Recoating2 - 4 hours
Full drying24 - 48 hours
Shelf life24 months in a sealed container, in a dry, well-ventilated place, away from heat and direct sun (10 to 30 ºC)

It offers high transparency and weather resistance, good resistance to abrasion, hot-cold cycles, water and humidity, and good resistance to alkalinity and efflorescence. It noticeably enhances the colour of stamped and concrete coatings while keeping the original texture. Full technical documentation is in the technical data sheet downloadable above.

Substrates

Cementitious surfaces and porous mineral bases: stamped concrete, microcement and concrete floors. The surface must be clean and free of moisture at the time of application.

How is it applied?

Water-based product, no dilution required: ready to use. After 72 hours from completion of the pavement, wash the surface and, when it is free of moisture, apply with a sprayer from a distance of 30-40 cm. Cover the entire surface, aiming for a uniform film, with no thick layers or puddles. Apply with ambient and substrate temperatures between 5 and 30 ºC and without excessive wind. Clean the tools with water immediately after use.

Compatibility

•  ESTonetex Pavimento: its technical data sheet recommends applying EST-Floor as the final protection once the work is finished

•  Stamped concrete and microcement: decorative and industrial pavements in stamped concrete or microcement, and concrete floors

•  Solvents and thinners: never use

Observations and precautions

Under certain conditions it may yellow over time, so it is not recommended for white or light-coloured surfaces. Non-flammable product. Good ventilation, a mask with chemical absorbent, protective goggles and rubber gloves; in case of skin contact, wash with soap and water, and if swallowed, do not induce vomiting and seek medical attention immediately. Close the lid well after each use to prevent the product from drying out or thickening. Keep out of the reach of children. Professional product: always consult the safety data sheet before use.

Storage

Store for up to 24 months in a sealed container, in a dry, well-ventilated place, away from heat sources and direct sunlight, at a temperature not below 10 ºC nor above 30 ºC. Expired product must be disposed of in accordance with current legislation.

Complementary materials

•  ESTonetex Pavimento: printed pavement mortar protected with this varnish

•  EST sprayer: to apply the varnish from 30-40 cm

•  EST-3 Plus N, EST-7 and EST-Multilitio: the other water repellents and sealers of the range

Frequently asked questions

What is EST-Floor used for?
To protect stamped concrete, microcement and concrete floors with a transparent film that improves curing and enhances colour.

Does it need to be diluted?
No: it is a water-based product, ready to use. Solvents or thinners must never be used.

When can it be applied after the pavement is completed?
After 72 hours from completion of the pavement, washing the surface first and when it is free of moisture.

How is it applied?
With a sprayer, from 30-40 cm, covering the entire surface with a uniform film and avoiding thick layers or puddles. Ambient and substrate temperature must be between 5 and 30 ºC, without excessive wind.

Is it suitable for light-coloured floors?
It is not recommended for white or light-coloured surfaces, because under certain conditions it may yellow over time.

What is its coverage and how long does it take to dry?
Coverage is 8 to 10 m² per litre on stamped concrete. It is touch dry in 1-2 hours, can be recoated after 2-4 hours and is fully dry in 24 to 48 hours.

How does it differ from EST-3 Plus N and EST-Multilitio?
EST-Floor is a water-based varnish that forms a protective film on the pavement. EST-3 Plus N is a mineral water repellent that leaves no film but penetrates the pore. EST-Multilitio is a lithium silicate consolidant to harden the mineral base.

Which mortar is it recommended with?
The technical data sheet of ESTonetex Pavimento recommends applying EST-Floor for greater protection once the work is finished.

Which containers and references does it come in?
In plastic containers of 5 L (REF 1209) and 25 L (REF 1210).

👉🏻 Remember that our shop is a DIGITAL CATALOGUE. You can request a quote if you are in Spain, or find our official international distributors.

Solicitud de presupuesto

También podría interesarte