Wood stamp kit KM1
Applications
• Creating wood and beam textures on moldable ESTonetex mortars, cementitious mortars and concrete
• Theming work and creation of textures in high-end decoration
• Combining roller and stamp and knot to vary the finish of the wood and beam texture
Technical specifications
| Reference | 2019 |
| Type | Kit of roller, stamp and knot for wood and beam textures |
| Measures · roller | 34 × 25 cm |
| Measures · stamp | 21 × 15 cm (with fabric handle) |
| Measures · knot | 8 × 5 cm |
This product has no technical data sheet: for any question about sizes, texture or compatibility, request information.
How is it used?
1. Spread the mortar over the surface to be textured.
2. Using the EST sprayer, apply EST-Desmoldeante onto the mortar and onto the roller, the stamp and the knot, until the surfaces are completely covered.
3. While the mortar is still soft, roll the roller over the surface, press the stamp section by section and add the knots where a wood knot is wanted.
4. Always clean the roller, the stamp and the knot after use, with a wire brush.
According to the EST-Desmoldeante technical data sheet: waiting times vary with temperature and humidity; the release agent application temperature must be between 5 and 35 ºC; do not use if the mortar has excess water, do not add water once it has been sprayed and do not apply if there is a risk of frost, rain, strong winds or direct sun; wear gloves.
Compatibility
• Moldable ESTonetex mortars: ESTonetex TXT (compatible with stamps according to the catalog), ESTonetex Park (compatible with molds), ESTonetex Sulfo and ESTonetex Extreme (carving and stamping) and ESTonetex Pavimento (anti-slip finish through texture or stamping). All of them in ESTonetex mortars
• Other mortars and substrates: also suitable for cementitious mortars and concrete while they are still soft
• Release agent: EST-Desmoldeante is the system release agent for molds and rollers; it prevents the mortar from sticking
Complementary materials
• EST-Desmoldeante: release agent for molds and rollers
• EST sprayer: to apply the release agent
• Wire brush: to clean the stamp after use
• ESTonetex mortars: range of mortars that can be stamped
• Wood stamps: MM1 / MM2 / MM3 / MM4 / MM5 / MM6 / MM7 / MM8
• Wood rollers: RM1 / RM2 / RM3
• See the full wood and trunk texture molds category and the rock and stone texture molds
Frequently asked questions
What does KM1 include?
It includes a roller of 34 × 25 cm, stamp of 21 × 15 cm and knot of 8 × 5 cm.
How do KM1, KM2 and KM3 differ?
KM1 includes roller, stamp and one knot (roller of 34 × 25 cm, stamp of 21 × 15 cm and knot of 8 × 5 cm); KM2, roller, stamp and two knots (roller of 35 × 26 cm, stamp of 19 × 13 cm, big knot of 14 × 8 cm and small knot of 4 × 4 cm); KM3, roller and stamp only (roller of 34 × 25 cm and stamp of 21 × 15 cm). Other kits: KM2 / KM3.
What textures is the kit for?
According to the catalog, for creating wood and beam textures.
What is the advantage of a kit over getting the roller, stamp and knot separately?
It brings together in one set the roller, the stamp and, depending on the kit, the knot to create wood and beam textures. Individual rollers, stamps and knots also exist: RM1 / RM2 / RM3; MM1 / MM2 / MM3; N1 / N3.
Which release agent should be used and when is it applied?
EST-Desmoldeante is recommended, sprayed onto the mortar and onto the kit tools, while the mortar is still soft.
Which mortars can it be used with?
With moldable ESTonetex mortars such as ESTonetex TXT, ESTonetex Park, ESTonetex Sulfo, ESTonetex Extreme or ESTonetex Pavimento, and with cementitious mortars and concrete while they are still soft.
How are the kit tools cleaned?
Always after use, with a wire brush.
👉🏻 Remember that our shop is a DIGITAL CATALOGUE. You can request a quote if you are in Spain, or find our official international distributors.
Solicitud de presupuesto
-- or --