Wood stamp MM4

Applications

•  Reproducing the texture of rustic wood and wooden beam on moldable ESTonetex mortars, cementitious mortars and concrete

•  Theming work and creation of textures in high-end decoration

•  Combination with rollers, knots and other stamps in the range to vary the surface finish

Technical specifications

This product has no technical data sheet: for any question about sizes, texture or compatibility, request information.

How is it used?

1. Spread the mortar over the surface to be textured.

2. Using the EST sprayer, apply EST-Desmoldeante onto the mortar and onto the stamp, until the surfaces are completely covered.

3. While the mortar is still soft, press the stamp onto the surface, holding it by the fabric handle, and repeat section by section until the whole area is covered.

4. Always clean the stamp after use, with a wire brush.

According to the EST-Desmoldeante technical data sheet: waiting times vary with temperature and humidity; the release agent application temperature must be between 5 and 35 ºC; do not use if the mortar has excess water, do not add water once it has been sprayed and do not apply if there is a risk of frost, rain, strong winds or direct sun; wear gloves.

Compatibility

•  Moldable ESTonetex mortars: ESTonetex TXT (compatible with stamps according to the catalog), ESTonetex Park (compatible with molds), ESTonetex Sulfo and ESTonetex Extreme (carving and stamping) and ESTonetex Pavimento (anti-slip finish through texture or stamping). All of them in ESTonetex mortars

•  Other mortars and substrates: also suitable for cementitious mortars and concrete while they are still soft

•  Release agent: EST-Desmoldeante is the system release agent for molds and rollers; it prevents the mortar from sticking

Complementary materials

•  EST-Desmoldeante: release agent for molds and rollers

•  EST sprayer: to apply the release agent

•  Wire brush: to clean the stamp after use

•  ESTonetex mortars: range of mortars that can be stamped

•  Wood rollers: RM1 / RM2 / RM3

•  Wood knots: N1 / N3

•  Roller, stamp and knot kits: KM1 / KM2 / KM3

•  See the full wood and trunk texture molds category and the rock and stone texture molds

Frequently asked questions

What texture does MM4 reproduce?
According to the catalog, it is a rustic wood and wooden beam texture stamp. It measures 60 × 20 cm and its reference is 2003.

Is it flexible or semi-flexible?
It is semi-flexible. In this range, the catalog classifies MM1, MM2, MM3, MM4, MM7, MM8, MM9, MM13 as semi-flexible and MM5, MM6, MM10, MM11, MM12 as flexible.

Does it have a handle?
It has a fabric handle. Like most MM stamps, it has a fabric handle; only MM1 has a plastic handle.

Which release agent should be used and when is the stamp applied?
EST-Desmoldeante is recommended, sprayed onto the mortar and onto the stamp. The stamp is applied while the mortar is still soft.

Which mortars can it be used with?
With moldable ESTonetex mortars such as ESTonetex TXT, ESTonetex Park, ESTonetex Sulfo, ESTonetex Extreme or ESTonetex Pavimento, and with cementitious mortars and concrete while they are still soft.

How does MM4 differ from the other stamps with the same texture?
The texture is of the same type (rustic wood and wooden beam); size, flexibility and handle change. MM4: 60 × 20 cm, semi-flexible, fabric handle. Others: MM3 (38 × 55 cm, semi-flexible, fabric handle), MM5 (103 × 26 cm, flexible, fabric handle) and MM6 (108 × 24 cm, flexible, fabric handle).

What is the difference between a stamp, a roller and a kit?
The stamp is pressed onto the soft mortar section by section; the roller is rolled over the surface; the kit combines roller, stamp and, depending on the kit, a knot to create wood and beam textures. Rollers: RM1 / RM2 / RM3. Kits: KM1 / KM2 / KM3.

How is it cleaned after use?
It is recommended to always clean it after use with a wire brush, so that mortar residue does not build up.