Stone roller RP1

Applications

•  Reproducing the texture of stone and rock on moldable ESTonetex mortars, cementitious mortars and concrete

•  Theming work and creation of textures in high-end decoration

•  Texturing surfaces by rolling section by section

Technical specifications

This product has no technical data sheet: for any question about sizes, texture or compatibility, request information.

How is it used?

1. Spread the mortar over the surface to be textured.

2. Using the EST sprayer, apply EST-Desmoldeante onto the mortar and onto the roller, until the surfaces are completely covered.

3. While the mortar is still soft, roll the roller over the surface, section by section, to imprint the texture.

4. Always clean the roller after use, with a wire brush.

According to the EST-Desmoldeante technical data sheet: waiting times vary with temperature and humidity; the release agent application temperature must be between 5 and 35 ºC; do not use if the mortar has excess water, do not add water once it has been sprayed and do not apply if there is a risk of frost, rain, strong winds or direct sun; wear gloves.

Compatibility

•  Moldable ESTonetex mortars: ESTonetex TXT (compatible with stamps according to the catalog), ESTonetex Park (compatible with molds), ESTonetex Sulfo and ESTonetex Extreme (carving and stamping) and ESTonetex Pavimento (anti-slip finish through texture or stamping). All of them in ESTonetex mortars

•  Other mortars and substrates: also suitable for cementitious mortars and concrete while they are still soft

•  Release agent: EST-Desmoldeante is the system release agent for molds and rollers; it prevents the mortar from sticking

Complementary materials

•  EST-Desmoldeante: release agent for molds and rollers

•  EST sprayer: to apply the release agent

•  Wire brush: to clean the stamp or roller after use

•  ESTonetex mortars: range of mortars that can be stamped

•  L stamps (rigid, plastic handle): L1 / L2 / L6 / L7 / L9 / L10

•  MR stamps (semi-flexible, plastic handle): MR1 / MR2 / MR3 / MR4

•  MP stamps (fabric handle): MP1 / MP2 / MP3 / MP4 / MP5

•  MF stamps (flexible, silicone handle): MF1 / MF2 / MF3 / MF4 / MF5

•  Roller and stamp kits: KP1 / KP2 / KP3 / KP4

•  See the full rock and stone texture molds category

Frequently asked questions

What texture does RP1 reproduce?
According to the catalog, it is a stone and rock texture roller. It measures 32 × 20 cm and its reference is 2116.

How does RP1 differ from the other rollers?
All the RP and RT rollers in the catalog are stone and rock texture rollers; the specific texture and the size change. RP1: 32 × 20 cm. Others: RP2 (31 × 21 cm), RP3 (32 × 20 cm), RP4 (32 × 24 cm), RP5 (32 × 23 cm), RP6 (33 × 23 cm), RP7 (32 × 23 cm), RP8 (32 × 23 cm), RP9 (32 × 23 cm), RT01 (26 × 12 cm) and RT02 (24 × 7 cm).

What is the difference between a roller and a stamp?
The roller is rolled over the surface; the stamp is pressed onto the soft mortar section by section. Stone stamps: L1 / L2 / L6 / MP1.

Are there kits that include a roller?
Yes: the KP kits combine a roller and a stamp with a fabric handle to create stone and rock textures (KP1 / KP2 / KP3 / KP4), and KPR1 brings together two rollers (big and small). Their sizes are on each product page.

Which release agent should be used and when is it applied?
EST-Desmoldeante is recommended, sprayed onto the mortar and onto the roller, while the mortar is still soft.

Which mortars can it be used with?
With moldable ESTonetex mortars such as ESTonetex TXT, ESTonetex Park, ESTonetex Sulfo, ESTonetex Extreme or ESTonetex Pavimento, and with cementitious mortars and concrete while they are still soft.

How is it cleaned after use?
It is recommended to always clean it after use with a wire brush, so that mortar residue does not build up.